Monday, January 26, 2015

The Tyne tandem is for sale

I've lost my extra storage space and the Tyne is the last of my project boats that has to go.  This kayak is 17' long and it weighs 80 or 90 pounds.  This might be a good boat for camping and fishing on flat water in warm weather, and probably not so good on rivers, or on the bay in windy (that is, summer) weather unless you can make or modify a spray skirt to fit it.  It doesn't include paddles but it might include the cart that I made for a canoe.  There are two seat backs but they aren't shown in the photos. 

The Tyne probably ought to be folded up and stored inside in cold or wet weather unless the wood parts have been refinished and the canvas has been treated with something to make it mildew resistant (or if the original skin has been replaced with a PVC skin).

The frame still needs some minor repairs: the new coaming board needs to be sanded or planed to make it thinner and more flexible; a crack in one of the floorboards needs to be glued up and maybe reinforced with a little fiberglass or some thin plywood.  One of the gunnels has a crack that should be reinforced with fiberglass or thin marine plywood.  There are a few other issues, none of which can't be handled be anyone with average DIY skills.


Skin repairs:  The skin is canvas with a waterproof coating from the gunnels down.  The stitching is broken in a couple of places, and the waterproof coating needs to be patched or filled with something like black 3M 5200, Sikaflex, etc.  (Aquaseal might work but I don't think it would be cost-effective.)   I was thinking about making a lightweight new skin for this boat as a practice run for making a skin for an aluminum-frame boat, but I probably will never get to it; you can find instructions for making a skin at Tom Yost's folding kayak site.



The wood frame needs some minor repairs, and it might have a cracked rib that should probably be glued closed and reinforced with fiberglass or thin marine plywood on one side.


None of the repairs require any special skills unless you want to restore the Tyne to it's original condition for some reason.  If I get around to making this boat completely seaworthy before I sell it I'll make seats from some type IV PFDs or a couple of old boogie boards attached to the frame with nylon straps so they don't slide.

Broken stitches.  I suppose I could use 3M 5400 or something like that instead of replacing the actual stitches, but I'll try stitching first if I ever get to it.
broken stitches


I might be willing to trade for kayak gear, and maybe for materials I can use to build a skin for a Yost Sea Tour aluminum-frame folder.  I'm in the SF east bay area.

Update: it's been sold.

Saturday, January 10, 2015

Kayak Paddle Bag

A paddle bag bag isn't a necessity, but it can be useful while schlepping all the gear from the apartment to the car and to wherever else it's going.  Most often I just put the bulky items (PFD, shoes, etc) into a plastic tub, and small items (clothes, camera, etc) into a canvas gear bag.  The gear bag goes on top of the tub and the paddle gets stuffed into the sides of the tub, so I can carry everything down to the street in one trip.  The problem is that the paddle ends hang up on everything and are just a nuisance.


The paddle bag should be something that can be slung over a shoulder, holds the paddles securely, and keeps the ends near the back of my head where they aren't too likely to get into trouble.  I've tested a variety of bags (day packs, duffels, chair bags, small guitar gig bags, a junior golf caddy bag, and others) from thrift stores and junk stores, and the leading candidate is...

The Nike baseball bag

A couple of years ago I bought this heavily worn baseball bat-and-helmet-and-stuff bag that seemed like it could be re-purposed as a paddle-and-gear bag.  The bag is dirty and and the zipper is broken and it has a lot of small holes worn in it - but it only cost $1, so I thought I'd see how it worked out.


What made the bat bag useful is the pocket that runs the length of the bag (about 2.5') and is meant to hold one or two baseball bats.  The pocket opens at the end of the bag.  The rest of the bag holds everything else, so it isn't necessary to unpack gear to get at the paddles, or vice versa.   (On this bag the zipper on the gear compartment is missing the slide, and it won't really hold anything.  I was going to add snaps or some other simple fix, but haven't gotten around to it.  The bag might also benefit from a Scotch Guard or other water-repellant treatment.)

As it is the bat pocket (also missing a zipper slide) is just wide enough so that the paddle blades can be put in one at a time.  My Aqua-Bound StingRay paddle fits, but a river paddle, generic aluminum-shaft paddles, and probably any kayak paddle that isn't a skinny touring paddle or a greenland paddle will be too wide for this particular bag.  A different bat bag might hold wider paddles.

The is a plastic snap at the end of the bat pocket where one end of a shoulder strap could be attached.  I might add a grommet with a loop of cord sticking out to attach the other end of the strap.  (I might actually sew on a strap loop when I get a bag in better condition.)

The short version: the Nike bag seems to keep the paddle parts securely bundled and the ends together.  The paddles can be removed without unpacking anything else, and there's lots of room for other gear.  For paddles with skinny blades only.   Needs to have a shoulder strap added. 

The Nike bat bag
The Nike bag with a 2-piece touring paddle in the bat pocket.  The gear compartment is empty.

The Nike bat bag
The paddle fit in the pocket one at a time, and it seems like there's no danger of them sliding out unexpectedly.

The Nike bat bag bat\paddle slot
The paddle blades are about 6.25" wide.  A wider blade won't fit in the bat pocket.

The end of the bat pocket with its broken zipper.

This is a gig bag for a small guitar and it works with wider paddles than the Nike bag, but otherwise it just isn't as useful.
The First Act gig bag with the wood paddle.

Homemade paddles

I made a two-piece paddle back when I got my first kayak...
2-piece wood paddle
The closet-pole-and-plywood paddle.
2-piece wood paddle
Two-piece wood paddle.
I had some marine plywood leftovers from an old project, and I traced the blades from a Sevlor paddle onto a couple of those and cut out the blades, as seen in the photos.  The Sevlor was the only paddle I had owned, back then, and I really didn't know what I was doing.  Half of the original closet rod had to be thrown out, and the new rod doesn't seem to match the old one, so the paddle is probably unbalanced as-is.

I never finished fitting the both parts to the ferrule, so the paddle is unfinished and has never been used.  The current plan is to make the blades narrower, thin the shafts a bit, and reduce the overall length.  The blades are epoxied to the shafts, but I put stainless screws in to keep the blades firmly attached, and I guess I can get rid of those.
The plywood is discolored after being in a sometimes damp storeroom for several years.
The aluminum ferrule, which isn't finished either.
Paddle two is a homemade greenland paddle.  It's made with redwood from the local big-box home improvement store, and some walnut, maple, and birch scraps that had been hanging around.  I had some small teak scraps that went on the tips.  This one wasn't finished either, since I lost my workspace before I got around to doing the final shaping and putting on a finish.

Greenland paddle.  Looks nice, but I think I used too much hardwood.  I'm going to try and thin it carefully to make it light without being flimsy.

The homemade GP, still unfinished.  This was originally going to be a two-piece paddle, but  I changed my mind,  and ended up with a really ugly scarf joint in the middle of the shaft.

 I made these paddles without much woodworking experience to draw on, using ordinary hand tools for most of the work, in cramped conditions, so nothing was done in an afternoon, or even overnight, and neither paddle is likely to be finished soon.